Bleaching of Microcrystalline Cellulose Produced by Gas-Phase Hydrolysis
Journal Title: Lesnoy Zhurnal (Russian Forestry Journal) - Year 2021, Vol 10, Issue 6
Abstract
One of the main consumers of microcrystalline cellulose (MCC) is the pharmaceutical industry, where MCC is used as a binder and filler in direct compression of tablets. MCC is produced by acidic hydrolysis of cellulose, which usually results in a decrease in whiteness. This is due to the destruction of sugars formed during hydrolysis and the subsequent formation of colored products. The composition and properties of these products depend on the method of hydrolysis, acid concentration, temperature, and process duration. One of the most promising methods for producing MCC is gas-phase hydrolysis of cellulose with hydrogen chloride gas-air mixtures. The method has a high rate of hydrolysis, low reagent and energy consumption. The requirements of the pharmaceutical industry determine the need to produce MCC with high whiteness. The research purpose is to select bleaching modes for MCC using sodium hypochlorite and hydrogen peroxide as bleaching agents. MCC produced by gas-phase hydrolysis of bleached wood pulp was used during the study. The whiteness and intensity of the yellow tint of MCC in the bleaching process were determined by digital colorimetry on a flatbed scanner. The paper shows that sodium hypochlorite and hydrogen peroxide allow achieving the whiteness not less than 90 % and the intensity of the yellow tint not more than 3 standard units. High-quality bleaching can be carried out even for MCC samples with an initial whiteness of about 40 %. The most effective bleaching agent is sodium hypochlorite when the pH of the bleaching solution is 2–3. Hydrogen peroxide also provides high whiteness of MCC at pH of 10–11. However, the consumption of active oxygen (AO) for bleaching is more than three times higher in comparison with the consumption of active chlorine (ACh). It was found that the dyes of MCC produced by gas-phase hydrolysis consist of two chromophore groups that decolorize at different rates. The easily oxidized group of components makes up about 90 % of the total amount of dyes, and the resistant to oxidation components make up about 10 % and determine the intensity of the yellow tint of MCC. The modes of bleaching MCC with sodium hypochlorite and hydrogen peroxide to product samples with whiteness comparable to that of imported samples were determined. For citation: Sizov A.I., Pimenov S.D., Stroiteleva A.D., Stroiteleva K.D. Bleaching of Microcrystalline Cellulose Produced by Gas-Phase Hydrolysis. Lesnoy Zhurnal [Russian Forestry Journal], 2021, no. 6, pp. 173–183. DOI: 10.37482/0536-1036-2021-6-173-183
Authors and Affiliations
A. I. Sizov, S. D. Pimenov, A. D. Stroiteleva, K. D. Stroiteleva
Keywords
Related Articles
- EP ID EP698349
- DOI https://doi.org/10.37482/0536-1036-2021-6-173-183
- Views 97
- Downloads 0
Natural Regeneration on Deadwood in the Primeval Forest Janj
The paper investigates the natural regeneration of downed deadwood in the Janj primeval forest. The old-growth forest is located in the southwestern part of the Republic of Srpska, which is dominated by dolomite geologic...
Improving the Performance of Working Bodies and Tribosystems of Harvester Technological Equipment
Ensuring the competitiveness of enterprises of the forest complex is largely due to the level of reliable and high-performance equipment use, since this achieves a significant increase in the efficiency of timber harvest...
Wood Microstructure of Pine Plantations with Different Initial Stocking Rate on Drained Peat Soil upon Fertilization and Herbicide Treatments
To secure a steady operation of large wood processing enterprises in north-west of the Taiga zone, accelerated coniferous forest cultivation appears to be the most promising. Treatments with mineral fertilizers and herbi...
Vegetation Fire Behavior Prediction
The necessity for predicting the behavior of vegetation fires, including forest fires, is keenly felt in a time of severe droughts, which periodically recur in this or that area, and their precise prediction is still ham...
Device for Wood-Cutting Tool Hardening
Choosing effective methods and devices for surface hardening of wood-cutting tools is problematic due to the variety of their designs and operating conditions. In this regard, the development of such devices becomes an u...