Вплив вмісту пінополістиролу на властивості легких стружкових плит Effect of the expanded polystyrene content on the lightweight particleboards properties

Abstract

Досліджено фізико-механічні властивості легких личкованих стружко-вих плит з різним вмістом пінополістиролу. Плити виготовляли в процесі од-ночасного гарячого склеювання обсмоленої карбамідоормальдегідним клеєм деревинної стружки із гранулами пінополістиролу та личкування лущеним березовим шпоном. Витрата клею становила 10% від маси абсолютно сухих частинок, а вміст пінополістиролу у вигляді гранул – 4, 7, 10 %. Плити завтовшки 18 мм виготовляли щільністю 350, 450 і 550 кг/м3 за температури пресування 200 °С, тиску пресування 2,4 МПа та часу пресування 0,23 хв/мм. Отримані плити випробовували на межу міцності під час статичного згинання, модуль пружності під час статичного згинання, межу міцності на розтяг перпендикулярно до площини плити, набрякання і водопоглинання після витримки у воді впродовж 2 і 24 год. На основі досліджень встановлено, що легкі стружкові плити, личковані лущеним шпоном, мають високі показники досліджуваних властивостей, які перевищують встановлені нормативні значення згідно зі стандартом CEN/TS 16368. Найвищі значення межі міцності під час статичного згинання мали плити без пінополістиролу і з вмістом пінополістиролу 7 %, дещо менші – з вмістом пінополістиролу 4 %, а найменші – із вмістом пінополістиролу 10 %. За вмісту пінополістиролу 7 % модуль пружності під час статичного згинання плит є найбільшим. Встановлено, що вміст пінополістиролу 4 і 7 % у плитах збільшує межу міцності на розтяг перпендикулярно до площини плити порівняно з плитами без вмісту пінополістиролу, а плити з вмістом пінополістиролу 10 % не досягають нормативних значень у досліджуваному інтервалі щільностей плит. Набрякання у воді та водопоглинання плит зменшується зі збільшенням у них вмісту пінополістиролу. The physical and mechanical properties of veneered lightweight particleboards with different contents of expanded polystyrene were investigated. The boards were made by hot gluing of wood particles with urea formaldehyde glue (UF) and granules of expanded polystyrene and by veneering of rotary-cut birch veneer. The UF glue consumption was 10% of the mass of absolutely dry wood particles. The boards of thickness 18 mm and different density of 350, 450 and 550 kg/m3 were made at pressing temperature of 200 °С, pressing pressure of 2.4 MPa and pressing time of 0.23 min/mm. To make the boards the 4, 7, 10 % of expanded polystyrene granules were added to wood particles. Modulus of rupture (MOR), modulus of elasticity (MOE), tensile strength perpendicular to the plane of the board (IB), thickness swelling and water absorption after 2 and 24 hours of immersion in the water of the samples of lightweight particleboards were determined. The results of the research were found that veneered lightweight parti-cleboards have high indexes of investigated properties that exceed the established normative values in accordance with CEN/TS 16368. The greatest values of the MOR had boards without expanded polystyrene and with 7% content of expanded polystyrene, some smaller - with the content of expanded polystyrene 4%, and the smallest - with a content of expanded polystyrene 10%. The MOE of boards with the content 7% of expanded polystyrene is greatest. It has been established that the content of expanded polystyrene 4 and 7% in boards increases the tensile strength perpendicular to the plane of the boards (IB) compared to the board without the contents of the expanded polystyrene. And the boards containing 10% expanded polystyrene do not reach the normative values in the studied range of boards densities. Thickness swelling and water absorption of boards decrease with increasing content of expanded polystyrene in them.

Authors and Affiliations

Pavlo Bekhta, Liubov Baizova

Keywords

Related Articles

Моделі оцінювання техногенних чинників під час виникнення пожеж на сховищах нафтопродуктів [Valuation models of anthropogenic factors during the appearance fires in the storage of petroleum products]

In the event of fire in the storage of petroleum prod-ucts, which can then develop into a man-made disaster or a catastrophe, there is need for simulation of the formation of dangerous factors of anthropogenic impact on...

Qualitative analysis of pellets produced from Jerusalem artichoke (Helianthus tuberosus L.)

The development of renewable energy constitutes a crucial role for the future as combustion of the plant biomass causes reduction of sulfur oxides and nitrogen oxides. The purpose of the work was to determine the basic e...

Поширення та ріст модрини європейської в умовах Кременецького горбогір’я [European larch expansion and growth in conditions of Kremenetsk hilly region]

On the area of Kremenets hilly region favorable microclimate and soil-hydrological conditions were formed for growth and development of European larch. In this region about 2 thousand hectares of plantations with part of...

Download PDF file
  • EP ID EP305519
  • DOI 10.15421/411718
  • Views 90
  • Downloads 0

How To Cite

Pavlo Bekhta, Liubov Baizova (2017). Вплив вмісту пінополістиролу на властивості легких стружкових плит Effect of the expanded polystyrene content on the lightweight particleboards properties. Наукові праці Лісівничої академії наук України, 15(), 140-146. https://www.europub.co.uk/articles/-A-305519