Wear Resistance Increase of Samples Tribomating in Oil Composite with Geo Modifier КGМF-1
Journal Title: Tribology in Industry - Year 2019, Vol 41, Issue 2
Abstract
Increase of wear resistance of different types of tribomating which are functioning in fluid lubrication is possible due to: choosing more expensive and high quality material of samples that is not always sensible; applying some wear resistant coatings on them; selection and formation of complex composition of oil additives. Due to nanomaterials development there is a possibility of efficient use of functional additives such as geo modifiers in tribology. Due to geo modifier-based oil composites use it’s not necessary to make any structural changes of machines mated parts though their wear resistance is increased. It requires the conducting of some experimental tribological research. It was found that oil media modified by a geo modifier increase the wear resistance of working surfaces of different types of tribomating. The use of geo modifier КGМF-1 (Katerynivka friction geo modifier -1 (patent of Ukraine №69657)) has been suggested. Lubrication quality of oil compositions based on М-10Г2К (M-10G2K) (motor oil of 10th viscosity grade, of group Г2К (G2K), for the CIS countries the oil grade conforms SAE 30) + КGМF-1 (4.0 - 4.5%) has been studied on a computer modernized four-ball friction testing machine ЧШМ-К1 (CHMK-К1). To evaluate the lubrication quality of the oil composite with the suggested geo modifier and to use the comparative analysis of the obtained results the research was conducted on commercial samples of base oil M-10G2K and oil composites M-10G2K + XADO Maximum for Diesel Truck (2.0 - 2.3%) (agent 2D sliding revitalization factor (RF) 100, revitalizant 1 Stage RF 100, metal conditioner RF 5.5), M-10G2K + cuprum glycerate (3.7 - 4.5%). Some average indices of wear, critical load, and welding load have been found. Samples division into 4 types of mating according to the following characteristic features: mobility, material hardness and friction area has been suggested for more accurate picture of wear resistance changes of samples tribomating which are functioning in base and modified oil. Lower friction torque of different samples couplings in modified oil by geo modifier КGМF-1 in comparison with base oil M-10G2K was recorded while using Friction machine 2070 SMT-1 with add-on module "ring-ring". The samples wear rate in modified oil by geo modifier КGМF-1 in comparison with base oil M-10G2K was studied by method of acoustic signal amplitude measurements directly from the friction zone by a commercially produced instrument of Brüel & Kjear company.
Authors and Affiliations
V. Aulin, S. Lysenko, O. Lyashuk, A. Hrinkiv, D. Velykodnyi, Y. Vovk
Keywords
Related Articles
- EP ID EP593767
- DOI 10.24874/ti.2019.41.02.02
- Views 93
- Downloads 0
Development of an Extrusion Process to Ameliorate the Tribological Properties of Heat Treated Al Mg Si (Cu) System Alloys Matrix Composites in Consolidated State
The developments of AA6061 aluminum matrix composites are of great interest in industrial applications for lighter materials with high specific strength, stiffness and wear resistance. In this article, the dry wear beha...
Mechanical, Spectroscopic and Micro-structural Characterization of Banana Particulate Reinforced PVC Composite as Piping Material
A banana particulate reinforced polyvinyl chloride (PVC) composite was developed with considerabley low cost materials having an overall light-weight and good mechanical properties for potential application as piping mat...
Wear Assessment of Fe-TiC/ZrC Hardfacing Produced from Oxides
The direct conversion of oxides into carbides during plasma transferred arc welding is a promising processing route to produce wear resistant overlays at low cost. In the present study, Fe-TiC and Fe-ZrC composite overla...
Analyzing the Surface Roughness Effects on Piston Skirt EHL in Initial Engine Start-Up Using Different Viscosity Grade Oils
The absence of fully developed fluid film lubrication between Piston and Liner surfaces is responsible for high friction and wear at initial engine start‐up. In this paper flow factor method is used in two dimensional Re...
Analysis of HD Journal Bearings Considering Elastic Deformation and Non-Newtonian Rabinowitsch Fluid Model
The purpose of this paper is to study the performance of a finite length journal bearing, taking into account effects of non-Newtonian Rabinowitsch flow rheology and elastic deformations of the bearing liner. According t...